Co-authored-by: Nate Brown <nbrown.us@gmail.com>
Co-authored-by: Jack Doan <jackdoan@rivian.com>
Co-authored-by: brad-defined <77982333+brad-defined@users.noreply.github.com>
Co-authored-by: Jack Doan <me@jackdoan.com>
If the host OS is already big endian, we were swapping bytes when we
shouldn't have. Use the Go helper to make sure we do the endianness
correctly
Fixes: #1189
We had to manually define these types before, but the latest release of
`golang.org/x/sys` adds these definitions:
- 6dfb94eaa3
Since we just updated with this PR, we can clean this up now:
- https://github.com/slackhq/nebula/pull/1161
On some systems, IPv6 is disabled (for example, CIS benchmark recommends to disable it when not used), but currently all UDP connections are using AF_INET6 sockets.
When we are binding AF_INET6 socket to an address like ::ffff:1.2.3.4 (IPv4 addresses are parsed by net.ParseIP this way), we can't send or receive IPv6 packets anyway, so this will not break any scenarios.
---------
Co-authored-by: Wade Simmons <wsimmons@slack-corp.com>
* add calculated_remotes
This setting allows us to "guess" what the remote might be for a host
while we wait for the lighthouse response. For networks that hard
designed with in mind, it can help speed up handshake performance, as well as
improve resiliency in the case that all lighthouses are down.
Example:
lighthouse:
# ...
calculated_remotes:
# For any Nebula IPs in 10.0.10.0/24, this will apply the mask and add
# the calculated IP as an initial remote (while we wait for the response
# from the lighthouse). Both CIDRs must have the same mask size.
# For example, Nebula IP 10.0.10.123 will have a calculated remote of
# 192.168.1.123
10.0.10.0/24:
- mask: 192.168.1.0/24
port: 4242
* figure out what is up with this test
* add test
* better logic for sending handshakes
Keep track of the last light of hosts we sent handshakes to. Only log
handshake sent messages if the list has changed.
Remove the test Test_NewHandshakeManagerTrigger because it is faulty and
makes no sense. It relys on the fact that no handshake packets actually
get sent, but with these changes we would send packets now (which it
should!)
* use atomic.Pointer
* cleanup to make it clearer
* fix typo in example
The goal of this work is to send packets between two hosts using more than one
5-tuple. When running on networks like AWS where the underlying network driver
and overlay fabric makes routing, load balancing, and failover decisions based
on the flow hash, this enables more than one flow between pairs of hosts.
Multiport spreads outgoing UDP packets across multiple UDP send ports,
which allows nebula to work around any issues on the underlay network.
Some example issues this could work around:
- UDP rate limits on a per flow basis.
- Partial underlay network failure in which some flows work and some don't
Agreement is done during the handshake to decide if multiport mode will
be used for a given tunnel (one side must have tx_enabled set, the other
side must have rx_enabled set)
NOTE: you cannot use multiport on a host if you are relying on UDP hole
punching to get through a NAT or firewall.
NOTE: Linux only (uses raw sockets to send). Also currently only works
with IPv4 underlay network remotes.
This is implemented by opening a raw socket and sending packets with
a source port that is based on a hash of the overlay source/destiation
port. For ICMP and Nebula metadata packets, we use a random source port.
Example configuration:
multiport:
# This host support sending via multiple UDP ports.
tx_enabled: false
# This host supports receiving packets sent from multiple UDP ports.
rx_enabled: false
# How many UDP ports to use when sending. The lowest source port will be
# listen.port and go up to (but not including) listen.port + tx_ports.
tx_ports: 100
# NOTE: All of your hosts must be running a version of Nebula that supports
# multiport if you want to enable this feature. Older versions of Nebula
# will be confused by these multiport handshakes.
#
# If handshakes are not getting a response, attempt to transmit handshakes
# using random UDP source ports (to get around partial underlay network
# failures).
tx_handshake: false
# How many unresponded handshakes we should send before we attempt to
# send multiport handshakes.
tx_handshake_delay: 2
