* Support NIST curve P256
This change adds support for NIST curve P256. When you use `nebula-cert ca`
or `nebula-cert keygen`, you can specify `-curve P256` to enable it. The
curve to use is based on the curve defined in your CA certificate.
Internally, we use ECDSA P256 to sign certificates, and ECDH P256 to do
Noise handshakes. P256 is not supported natively in Noise Protocol, so
we define `DHP256` in the `noiseutil` package to implement support for
it.
You cannot have a mixed network of Curve25519 and P256 certificates,
since the Noise protocol will only attempt to parse using the Curve
defined in the host's certificate.
* verify the curves match in VerifyPrivateKey
This would have failed anyways once we tried to actually use the bytes
in the private key, but its better to detect the issue up front with
a better error message.
* add cert.Curve argument to Sign method
* fix mismerge
* use crypto/ecdh
This is the preferred method for doing ECDH functions now, and also has
a boringcrypto specific codepath.
* remove other ecdh uses of crypto/elliptic
use crypto/ecdh instead
* firewall: add option to send REJECT replies
This change allows you to configure the firewall to send REJECT packets
when a packet is denied.
firewall:
# Action to take when a packet is not allowed by the firewall rules.
# Can be one of:
# `drop` (default): silently drop the packet.
# `reject`: send a reject reply.
# - For TCP, this will be a RST "Connection Reset" packet.
# - For other protocols, this will be an ICMP port unreachable packet.
outbound_action: drop
inbound_action: drop
These packets are only sent to established tunnels, and only on the
overlay network (currently IPv4 only).
$ ping -c1 192.168.100.3
PING 192.168.100.3 (192.168.100.3) 56(84) bytes of data.
From 192.168.100.3 icmp_seq=2 Destination Port Unreachable
--- 192.168.100.3 ping statistics ---
2 packets transmitted, 0 received, +1 errors, 100% packet loss, time 31ms
$ nc -nzv 192.168.100.3 22
(UNKNOWN) [192.168.100.3] 22 (?) : Connection refused
This change also modifies the smoke test to capture tcpdump pcaps from
both the inside and outside to inspect what is going on over the wire.
It also now does TCP and UDP packet tests using the Nmap version of
ncat.
* calculate seq and ack the same was as the kernel
The logic a bit confusing, so we copy it straight from how the kernel
does iptables `--reject-with tcp-reset`:
- https://github.com/torvalds/linux/blob/v5.19/net/ipv4/netfilter/nf_reject_ipv4.c#L193-L221
* cleanup
This makes it easier to use the docker container smoke test that
GitHub actions runs. There is also `make smoke-docker-race` that runs the
smoke test with `-race` enabled.
Test that basic inbound / outbound firewall rules work during the smoke
test. This change sets an inbound firewall rule on host3, and a new
host4 with outbound firewall rules. It also tests that conntrack allows
packets once the connection has been established.
* Better config test
Previously, when using the config test option `-test`, we quit fairly
earlier in the process and would not catch a variety of additional
parsing errors (such as lighthouse IP addresses, local_range, the new
check to make sure static hosts are in the certificate's subnet, etc).
* run config test as part of smoke test
* don't need privileges for configtest
Co-authored-by: Nathan Brown <nate@slack-corp.com>
This change adds a new Github Action, a 3 node smoke test. It starts
three docker containers (one lighthouse and two standard nodes) and
tests that they can all ping each other. This should hopefully detect
any basic runtime failures in PRs.
